TELECOMMUNICATIONS
METAL TELECOMMUNICATIONS MASTS
We design and manufacture different self-supporting metal towers specifically for telecommunications use: telephony, radio, television, antenna support, CCTV cameras, etc.
AZ MASTS

alumbrado

AZ-type lattice supports formed by hot-rolled steel corner profiles, with screw joints.


These supports are used for the installation of antennas, lightning conductors, accessible platforms for the installation of lighting fixtures or any other accessory required.

CHARACTERISTICS

  • Exterior steps
  • Intermediate footrests.
  • Approved fall protection system (lifeline).
  • Protection against corrosion by means of hot-dip galvanising.
  • Daytime marking paint in accordance with the International Civil Aviation Organisation.


FOUNDATIONS
anclaje
Model Height Loose terrain
(K=8Kg/cm3)
Normal terrain
(K=12Kg/cm3)
Hard terrain
(K=12Kg/cm3)
h(m) a (m) h (m) a (m) h (m) a (m)
AZ-900 12m 2,10 1,00 1,80 1,00 1,60 1,00
15m 2,10 1,10 1,90 1,05 1,70 1,05
18m 2,25 1,10 1,97 1,05 1,70 1,05
20m 2,25 1,20 2,05 1,10 1,85 1,10
22m 2,25 1,25 2,05 1,15 2,00 1,20
24m 2,30 1,30 2,10 1,15 2,00 1,10
26m 2,35 1,30 2,15 1,15 2,00 1,10
28m 2,35 1,35 2,15 1,25 2,00 1,15
30m 2,35 1,50 2,15 1,35 2,05 1,15
AZ-1000 12m 2,20 1,15 2,00 1,10 1,80 1,10
15m 2,25 1,30 2,10 1,15 1,95 1,10
18m 2,30 1,45 2,20 1,20 2,00 1,15
20m 2,30 1,52 2,20 1,25 1,05 1,20
22m 2,30 1,62 2,20 1,35 2,05 1,30
24m 2,33 1,68 2,25 1,36 2,09 1,30
26m 2,38 1,70 2,29 1,40 2,14 1,31
28m 2,41 1,75 2,32 1,43 2,15 1,37
30m 2,45 1,77 2,35 1,47 2,19 1,39
32m 2,45 1,80 2,35 1,49 2,20 1,40
34m 2,45 1,84 2,35 1,53 2,20 1,40
36m 2,45 1,91 2,35 1,60 2,20 1,50
38m 2,45 1,98 2,35 1,66 2,20 1,56
40m 2,45 2,04 2,35 1,73 2,20 1,63
42m 2,45 2,11 2,35 1,79 2,20 1,69


AZ are supplied on request - 2000 and 3000 effort 2000-3000daN
SHEET METAL MASTS WITH CONCRETE FOUNDATION

alumbrado

Concrete foundation sheet metal masts are octagonal-section, truncated-pyramidal masts made of folded steel sheet which are attached to the ground using a base plate and anchor bolts.

CHARACTERISTICS

  • Shaft with one or two sections.
  • Concreting of lower section to prevent oscillations produced by buckling due to wind loads.
  • Interior conduits for wiring.
  • Upper support for TV camera or any element required.
  • Upper and lower access door and support for panel board.
  • Protection against corrosion by means of hot-dip galvanising.
FOUNDATIONS:
As these supports are used for different applications, the manufacturer must be consulted on the foundation of each case.